585HE-12ga From Hell Guy

[hubel585]

There are guys on Castboolits forum experimenting with
locking on plastic bases securely on slugs.
Making their own front heavy ones for smoothbores.

Here is picture of our 585BB case next to long 585HE.




Here is another view of the great camo job on the
585HE Enfield, a top view. Ed

[hubel585]

Here is a helix driver seal we made by cutting base from helix driver

wadcup, good for fullbore roundballs that are too big to go in cup.

Best one to cut off is shortest `12ga one BPI has.






Here is picture of a 585HE made on a Stiller bolt action for guy in Canada.

It was made for the poster Spooksar on Africa Hunting and Accuratereloading,

by Corlanes/Rocky Mountain rifles, in Dawson Creek BC Canada, with a

Stiller action, Timney trigger. the stock is a blue/grey laminate. He imported

the barrel, cases, dies, etc.. from us, through Prophet River in Lloydminster AB.






That action similar to Lawton we had and neighbor got, that won the King Of The

2 Mile shoot at Whittington, with the 375 Lethal cartridge the neighbor made,

from our 585 brass. Made it full length case,.. It is big one on the right.

He made an 18 lb gun with McMillan target stock, a huge scope, tripod..

Nice thing is we don't need BMG action.ED

[hubel585]

Fellow big bore nut, Nathan Vale in AUS, has worked with

Bertram and got the run of full length 12ga From Hell cases done.

Drawn 12ga long cases as strong as BMG brass with unbreakable rims.

Any wanting to get some, contact Bertram at the email -----

b.bertram1@bigpond.com ......





Some more on wildcat 375 Lethal.......

.375 Lethal Precision Arms LLC rifle shooting prototype solid 400gr Berger bullets.

Mitchell built this rifle himself using a McMillan A5 Super Mag stock, Rock Creek barrel,

Nightforce ATACR MOA scope, Phoenix Precision Bipod, and a Lethal Precision Arms

muzzle brake. Lawton Action. Lethal Precision his own gunsmith shop, will make

these target rifles for anyone into target shooting and long range hunting..


Remarkably, Mitchell nailed first- and second- shot hits at the 2477-yard target,

a full 1.4 miles away. It is windy out there, makes shooting hard with a time limit.

The prototype 400 grain Berger Bullets solid performed great, (G7 BC of 0.56 at 3000 fps).






Here is 585 HE in an Enfield, in a Choate Heavy Varmint Stock. These are super strong.

The butts of these can easily be weighted. Couple guys doing them....... Ed

[hubel585]

Here is a picture of the 12ga FH brass case that Nathan

Vale had Bertrams make. Next to short plastic case.




Here is a picture of our 585BB headstamp. Perfect lettering

for our case as it came from production line,.




I like Hogue stocks, but they aren't made for singleshots.

We use singleshots for our 12ga FH and 585HE.

Here is picture of a NEF we set up for 24ga FH and we adapted

a Hogue 1300 Winchester Hogue to it. Looks a lot better, and

handles recoil easier than factory, Butt hollow, easy to add weight,





Here is picture of 585 case in the Lawton bolt, and the wildcat

375s and others made from our cases, work in bolt also. Ed

[BigDog58]

Fellow big bore nut, Nathan Vale in AUS, has worked with

Bertram and got the run of full length 12ga From Hell cases done.

Drawn 12ga long cases as strong as BMG brass with unbreakable rims.

Any wanting to get some, contact Bertram at the email -----

b.bertram1@bigpond.com ......





Some more on wildcat 375 Lethal.......

.375 Lethal Precision Arms LLC rifle shooting prototype solid 400gr Berger bullets.

Mitchell built this rifle himself using a McMillan A5 Super Mag stock, Rock Creek barrel,

Nightforce ATACR MOA scope, Phoenix Precision Bipod, and a Lethal Precision Arms

muzzle brake. Lawton Action. Lethal Precision his own gunsmith shop, will make

these target rifles for anyone into target shooting and long range hunting..


Remarkably, Mitchell nailed first- and second- shot hits at the 2477-yard target,

a full 1.4 miles away. It is windy out there, makes shooting hard with a time limit.

The prototype 400 grain Berger Bullets solid performed great, (G7 BC of 0.56 at 3000 fps).






Here is 585 HE in an Enfield, in a Choate Heavy Varmint Stock. These are super strong.

The butts of these can easily be weighted. Couple guys doing them....... Ed

Nice picture of him shooting at the NRA Whittington Center in Raton, NM. The winds can be quite a challenge there. Don't ask how I know

[hubel585]

Especially with time limit and you can't set for long time

waiting for wind to go down. Folks getting interested, I just took Mitch

over 2 more big boxes of cases to make 375s, as he got some orders

for ELR guns and case and die packages.Ed

[hubel585]

Our friend Brian from the far north went to Africa with his 24ga FH he did in
a NEF break action and got 3 nice buffs with it. Good job.


Our 585HE, 700HE and the great 12ga FH are now in the new COTW book
published in Oct, now out for sale,




We now have our target 375 HE cartridge, made by necking down our 585 HE.
The others couldn't make enough 375s, so we started our own. It has different
shoulder taper, length, neck length, improved over the others...Got a bunch
guys doing it, most into the 2 mile shooting venues, We're making cases,
testing, reamer prints at reamer guys, we are getting guys going. The 2 mile
shoot last year really got the interest booming for 375 necked from our case,

Here's how, size and seat 375 HE, one simple die, a 1" die, no huge dies needed
A die we can make with resize reamer from reamer guy, a regular die body,then
pass on to the next guy, one reamer can make whole bunch of dies for folks.

I do primer work separate, not in the press. SO First with lock ring set, I size cases.

When coming back out of dies with case, we notice the case still well centered,
held straight, when it is down as far as the length of the 375 HE neck... IE
the sides and shoulder corner still supported tight.

So we put washer or another lock ring on, same thickness as neck length,
below original lock ring, screw down tight tight in press,

Dies had a 5/8 x 24 thread in top, had powder fill bushing and other stuff same thread,
reamed out from bottom to set bullet height, with ram, case,and bullet up,

After priming, loading in the powder charge, we carefully start(boat tail makes it easy)
bullet in case by hand, slide up in die, into holder, raise ram to to top, bullet seated
perfect. Die can have different thread in top as long as big enough to hold seating
bushing of some kind , that can be made from many items.

These target bullets held in by strong neck tension, no crimping needed, and notice
bullet point will get no marks or dents, fast, easy, no 380-500 buck special dies.
Bushing centering bullet on ogive is very accurate.

OVER 900 375HE cases piled behind presses getting done. About 600 on another
bench nearly ready. Small batches in shelves.And we will do more.

All 375 info, prints, specs, pictures, load data, etc, is public domain, worldwide,
for any target, hunting, etc, use..Ed

[Holland&Holland]

Wow. I love the updates. Good work.

[OldmanFCSA]

Are these the same cases being used to create the 375 Lethal ?

[hubel585]

Yes same case, Mitch is a neighbor.

Here is picture of one of 3 buffs our guy from Canada got in

Africa with our 24ga FH he did on a NEF, in 2nd picture








Here is the neck die setup, with insert stems/plugs for the top that

are set in .020" steps to make our 375 HEs shown behind

from our 585HE cases. 900 cases behind and 600 on

another bench, mostly done, and 600 started elsewhere,

We also made a hydraulic form die, 375 HE test gun, starting with

lighter bullets, for example got 340 gr to 3700,

Will test up to 400gr We will find top speeds and powders needed

to get that, and have info where to get powders. Reamer prints are

at reamer guys, all prints and info is public domain... Ed

[hubel585]

Picture of fellows at Vestals Gunsmithing test firing 585 HE

they built for a guy. They got 750 gr to almost 2800 from

ultra short barrel, not a full load . A regular barrel would be

over 2900, 14000 ft lbs with full load..





Picture of our 375 HE cases, with little 378 WEA on left.

Middle case is with 330 gr, right case is 400gr bullet.




Here is picture of out 375HE testgun, in heavy t-hole stock.

So far 340 gr to 3700 and 360gr 3600.




Next 416 HE target case, these run through the hydro-die,

test gun done,will complete testing soon, to confirm specs.

When specs set, info will be sent to reamer guys

Soon will have 408 HE with specs set up also, for guys,

Smaller case 416s and 408s can be reamed out for

our bigger case .Ed

[gun_fan111v2]

Nice!

[BigDog58]

Picture of fellows at Vestals Gunsmithing test firing 585 HE

they built for a guy. They got 750 gr to almost 2800 from

ultra short barrel, not a full load . A regular barrel would be

over 2900, 14000 ft lbs with full load..

Any idea how many rounds your barrel throat will survive through, pushing these that hard? With the 50 BMG, throat erosion is a problem, once we start pushing 808gr & 800gr at those top speeds. We calculated our match running at about 2850-2875 fps and a little over 14,000 ft lbs at the muzzle. These are through a 33"-34" barrel, with a very tight throat and shooting turned brass Bore-riders.

Lastly, what powders are you guys running to get a 750gr running 2900 fps?

[Seismic Sam]

Okay, what's the BC on that 400 grain bullet??

[OldmanFCSA]

Okay, what's the BC on that 400 grain bullet??

G1 or G7 ?

G1 really doesn't apply.

G7 is dependent on an average of data obtained at many different distances.




In other words - I don't know.