585HE-12ga From Hell Guy

[Ghost]

That’s an impressive barrel

[OldmanFCSA]

Kenny makes great barrels - I use his barrels exclusively in my builds.

Who did the assembly work on your rifle shown above ???

[crbutler]

The OP is a guy named Ed Hubel. He makes these things, although some other guys build them as well.

Personally, although I handle recoil pretty well, the idea of shooting a high speed .577 NE scares me.

[hubel585]

I just do cases, load development for start and max.... and cheap guns

on Enfields and test guns. That gun was done by the owner...

And have got 460 HSM specs setup, the impetus for that is some
asking about one and new great line of 458 bullets CEB now has.

It will hold more powder than the 416 HSM and will get
a 572 gr as fast as 416 HSM gets a 475gr.....Ed..

[Holland&Holland]

The OP is a guy named Ed Hubel. He makes these things, although some other guys build them as well.

Personally, although I handle recoil pretty well, the idea of shooting a high speed .577 NE scares me.

YOLO

[hubel585]

The guys that did the super accurate 416 HE did another
416 HE that has an 8" longer 42 inch K&P barrel..

Used a Stiller action and same load with 475 gr bullet, as in
first gun and and gained about 200 fps with good accuracy.
3065 fps. Tested 2 groups of 3 and less than 1/2 min moa.

And loads they used are not the highest speed loads
the cartridge is capable of....Here is print with specs for
the 416 HE reamer chamber ....Ed....

[hubel585]

More about he guys that did the accurate 416 HE, they did a
416 HE that has an 8" longer 42 inch K&P barrel..

Used longer barrel and the same load with 475 gr bullet, as used
in the first gun and and gained about 200 fps with good accuracy,.
3065 fps. Tested 2 groups of 3 and less than 1/2 min moa.

And loads they used are not the highest speed loads
the cartridge is capable of....Here is picture.......Ed....

[Rotary12]

Ban him, he is just trying to sell his stuff.

[Holland&Holland]

Ban him, he is just trying to sell his stuff.

?????

[hubel585]

Away for a time, sickness..

Above guns built by others with 95% of cost spent elsewhere..
On all guns in my calibers worldwide, figures out, nearly 100%
costs elsewhere, I just get little glory, as the saying goes..

Here is print with chamber reamer specs for the
416 HSM chamber..There are 3 base sizes we have,
depending on actions used. Got reamers for all 3..
Got cases for all of them..
Our cases are public domain, so that is why I post
info and specs. To help guys do their own setups.
Manson makes reamers I use,,, Ed.

[hubel585]

Here is reamer print with chamber reamer specs for
the 460 HSM chamber .Couple guys getting set
to do 38-40 inch heavy 458 target barrels...Ed....

[hubel585]

With 40 inch barrel 416 HSM ,475 gr, get 3650, over 13,000 ft lbs muzzle energy.
Got guys getting set to have 38-40 inch 458 barrels made for 460 HSM.Ed..

[hubel585]

More info on this gun, we did it for testing 416 HSM with a rebated rim,
to check in intermediate size actions, with the longer, stronger, bolt lugs, Ed..

[hubel585]

Here is experimental action for 416 HSM in a heavy
stock....We lengthened port a little, set bolt stop back ,
opened bolt face fit the 416 HSM rebated rim. Ed.

Here is comparison of Montana PH to Pierce action we
modified to use for rebated rim 416 HSM testing..Ed.

[stonegraham]

he dosent deserve any ban, you guys shoud chill out