bullet weight and twist rate

Discussion of rifles, shotguns, and muzzleloaders

bullet weight and twist rate

Postby JoeH on Sun Aug 02, 2009 5:44 pm

I'm going to buy a heavy barrel 308 Winchester. My primary use, initially, will be for recreational shooting at the gun club. I may want to try F-class (out to 600 yd) at some point down the road. I may also use this rifle for deer or coyotes but chances are slim.

So, I'm researching rifles and finding several twist rates. Rifles in which I'm interested have the following twists: 1:10, 1:11.25, and 1:12.

What bullet weights will I want to be using and which twist rates are best for those weights?

Thanks!
Joe
Not a Glock Certified Armorer
User avatar
JoeH
 
Posts: 3687 [View]
Joined: Fri Jul 27, 2007 9:56 am
Location: 1911 JMB Drive

Re: bullet weight and twist rate

Postby JFettig on Sun Aug 02, 2009 6:01 pm

I haven't really seen any reasons to get a slower twist rate. My FN has a 1:12 twist rate and I've shot projectiles from 150gr to 190gr.
A faster twist is better for bigger projectiles. I turned some projectiles that should be nice long range projectiles but I don't have fast enough twist in my rifle.

Does anyone have any reason not to go with with a faster twist?

My whisper has 1:8 twist and I've shot small projectiles with no ill effects.


Jon
User avatar
JFettig
 
Posts: 945 [View]
Joined: Thu Jul 26, 2007 5:17 pm
Location: Forest Lake

Re: bullet weight and twist rate

Postby Rip Van Winkle on Sun Aug 02, 2009 6:39 pm

In 30 cal I think the old stand by was 1-12, although I think the M1 and M14 are 1-10. Some of the Palma guys I know are running 1-14 to 1-15, but their shooting 155gr bullets @ around 2900+ fps exclusively.

Unless you're planning on shooting some of the lighter thinner skinned bullets, say in the 125gr class, I'd go with a 1-10.
I will never apologize for being an American.
Post 435 Gun Club
North Star Rifle Club
cmpofficer@post435gunclub.org
DR #2673
President's Hundred (#48 2018)
Certified NRA RSO
User avatar
Rip Van Winkle
 
Posts: 4229 [View]
Joined: Thu Jul 26, 2007 5:04 pm
Location: Unfashionable end of the western spiral arm, Galaxy Milky Way

Re: bullet weight and twist rate

Postby ChefBo on Sun Aug 02, 2009 7:11 pm

Bullet rate and twist rate, 1:10 1:11/25 1:12
Ive always understood:
The lower the twist rate , The heavier the bullet.

If this is not correct, please advise which would be .

Thank you
ChefBo
 
Posts: 15 [View]
Joined: Wed Nov 12, 2008 6:44 pm
Location: MINNEAPOLIS

Re: bullet weight and twist rate

Postby Sigfan220 on Sun Aug 02, 2009 7:29 pm

I usualy refer to the Shilen site. My 243 has a Shilen crome-moly barrel in 1:10 twist. I didn't have much of a choice in the twist rate, it was a pre threaded short chambered barrel from either Midway or Brownells.

http://www.shilen.com/calibersAndTwists.html
User avatar
Sigfan220
 
Posts: 1110 [View]
Joined: Mon Mar 02, 2009 8:04 pm
Location: Crystal, MN

Re: bullet weight and twist rate

Postby Rip Van Winkle on Sun Aug 02, 2009 8:21 pm

The heavier the bullet in any given caliber the longer it will be and it will need a faster twist barrel to stabilize it.

There is a formula to figure out the proper twist for a given bullet but alas, I don't have it.
I will never apologize for being an American.
Post 435 Gun Club
North Star Rifle Club
cmpofficer@post435gunclub.org
DR #2673
President's Hundred (#48 2018)
Certified NRA RSO
User avatar
Rip Van Winkle
 
Posts: 4229 [View]
Joined: Thu Jul 26, 2007 5:04 pm
Location: Unfashionable end of the western spiral arm, Galaxy Milky Way

Re: bullet weight and twist rate

Postby TC95GT on Sun Aug 02, 2009 8:46 pm

"It is not enough to just obey Big Brother, you must love him, too." 1984 by George Orwell
User avatar
TC95GT
 
Posts: 1221 [View]
Joined: Thu Jul 26, 2007 4:19 pm


Return to Long Guns

Who is online

Users browsing this forum: No registered users and 2 guests

cron